XENOY™ Resin X2500UV PC PET
Plastic Granules
Associated Documents
TDS - Europe
Typical property data
Physical Properties
- Specific Gravity: 1.21 (ASTM D792)
- Density: 1.21 g/cm³ (ISO 1183)
- Melt Flow Rate: 9 g/10 min at 265°C/2.16 kgf (ASTM D1238)
- Melt Volume Rate: 4 cm³/10 min at 265°C/1.2 kg (ISO 1133)
- Water Absorption: 0.7% at 23°C/saturated (ISO 62-1)
- Moisture Absorption: 0.2% at 23°C/50% RH (ISO 62)
- Mold Shrinkage, Flow: 0.5–0.8% on tensile bar (SABIC method)
- Mold Shrinkage, Flow: 0.5–0.8% at 3.2 mm (SABIC method)
- Mold Shrinkage, Cross Flow: 0.5–0.8% on tensile bar (SABIC method)
Mechanical Properties
- Tensile Stress at Yield: 53 MPa (ASTM D638)
- Tensile Stress at Yield, Type I, 50 mm/min: 56 MPa (ASTM D638)
- Tensile Stress at Break, Type I, 50 mm/min: 55 MPa (ASTM D638)
- Tensile Strain at Yield: 5% (ASTM D638)
- Tensile Strain at Break: 100% (ASTM D638)
- Tensile Strain at Yield, Type I, 50 mm/min: 5% (ASTM D638)
- Tensile Strain at Break, Type I, 50 mm/min: 80% (ASTM D638)
- Tensile Modulus: 2200 MPa at 50 mm/min (ASTM D638)
- Flexural Stress: 79 MPa (ASTM D790)
- Flexural Stress at Yield: 79 MPa at 1.3 mm/min, 50 mm span (ASTM D790)
- Flexural Modulus: 2100 MPa (ASTM D790)
- Flexural Modulus: 2150 MPa at 1.3 mm/min, 50 mm span (ASTM D790)
- Taber Abrasion: 20 mg/1000 cycles, CS-17, 1 kg (SABIC method)
- Tensile Stress at Yield: 57 MPa at 50 mm/min (ISO 527)
- Tensile Stress at Break: 56 MPa at 50 mm/min (ISO 527)
- Tensile Strain at Yield: 5% at 50 mm/min (ISO 527)
- Tensile Strain at Break: 70% at 50 mm/min (ISO 527)
- Tensile Modulus: 2200 MPa at 1 mm/min (ISO 527)
- Flexural Stress at Yield: 80 MPa at 2 mm/min (ISO 178)
- Flexural Modulus: 2150 MPa at 2 mm/min (ISO 178)
- Ball Indentation Hardness: 95 MPa, H358/30 (ISO 2039-1)
Impact Properties
- Izod Impact, Notched: 600 J/m at 23°C (ASTM D256)
- Izod Impact, Notched: 450 J/m at 0°C (ASTM D256)
- Izod Impact, Notched: 200 J/m at -30°C (ASTM D256)
- Instrumented Dart Impact Total Energy: 60 J at 23°C (ASTM D3763)
- Izod Impact, Unnotched: NB at -30°C, 80 × 10 × 4 mm (ISO 180/1U)
- Izod Impact, Notched: 40 kJ/m² at +23°C, 80 × 10 × 4 mm (ISO 180/1A)
- Izod Impact, Notched: 25 kJ/m² at -30°C, 80 × 10 × 4 mm (ISO 180/1A)
- Izod Impact, Notched: 15 kJ/m² at -40°C, 80 × 10 × 4 mm (ISO 180/1A)
- Charpy Impact, V-Notch Edgewise: 50 kJ/m² at 23°C, 80 × 10 × 4 mm, span 62 mm (ISO 179/1eA)
- Charpy Impact, V-Notch Edgewise: 30 kJ/m² at -30°C, 80 × 10 × 4 mm, span 62 mm (ISO 179/1eA)
- Charpy Impact, Unnotched Edgewise: NB at -30°C, 80 × 10 × 4 mm, span 62 mm (ISO 179/1eU)
Thermal Properties
- Vicat Softening Temperature, Rate B/50: 135°C (ASTM D1525)
- Heat Deflection Temperature: 108°C at 1.82 MPa, 3.2 mm, unannealed (ASTM D648)
- Coefficient of Thermal Expansion, Flow: 8.0E-05 1/°C from -40°C to 40°C (ASTM E831)
- Coefficient of Thermal Expansion, Cross Flow: 8.5E-05 1/°C from -40°C to 40°C (ASTM E831)
- Thermal Conductivity: 0.18 W/m·°C (ISO 8302)
- Coefficient of Thermal Expansion, Flow: 8.2E-05 1/°C from 23°C to 80°C (ISO 11359-2)
- Coefficient of Thermal Expansion, Cross Flow: 8.7E-05 1/°C from 23°C to 80°C (ISO 11359-2)
- Ball Pressure Test: Passes at 125°C ± 2°C (IEC 60695-10-2)
- Vicat Softening Temperature, Rate A/50: 145°C (ISO 306)
- Vicat Softening Temperature, Rate B/50: 135°C (ISO 306)
- Vicat Softening Temperature, Rate B/120: 136°C (ISO 306)
- HDT/Af: 108°C at 1.8 MPa, flatwise 80 × 10 × 4 mm, span 64 mm (ISO 75/Af)
Electrical Properties
- Volume Resistivity: >1.0E+14 Ω·cm (IEC 60093)
- Surface Resistivity, ROA: >1.0E+15 Ω (IEC 60093)
- Dielectric Strength: 17 kV/mm in oil, 3.2 mm (IEC 60243-1)
- Relative Permittivity: 3.1 at 1 MHz (IEC 60250)
- Relative Permittivity: 3.3 at 50/60 Hz (IEC 60250)
- Dissipation Factor: 0.002 at 50/60 Hz (IEC 60250)
- Dissipation Factor: 0.02 at 1 MHz (IEC 60250)
Flame Characteristics
- UL Flame Class Rating: 94HB at 1.5 mm (UL 94 by SABIC-IP)
- Glow Wire Flammability Index: Passes 750°C at 2.7 mm (IEC 60695-2-12)
Injection molding Processing
- Drying Temperature: 110–120°C
- Drying Time: 4–6 hours
- Maximum Moisture Content: 0.02%
- Melt Temperature: 265–275°C
- Nozzle Temperature: 260–275°C
- Front Zone 3 Temperature: 260–280°C
- Middle Zone 2 Temperature: 250–275°C
- Rear Zone 1 Temperature: 240–270°C
- Hopper Temperature: 60–80°C
- Mold Temperature: 60–100°C
Use & Applications
- Automotive exterior parts
- Outdoor molded components
- Housings
- Applications requiring UV stability, heat resistance, and impact performance